Maple Leaf Diamond Hop Up Bucking

Price range : €9.90 to €9.90
€9.90
This item can be backordered
Gummihärte:

2021 Super Macaron Hup Up Bucking

Speziell für kältere Jahreszeiten geeignet.

Price range : €9.90 to €9.90
€9.90
This item can be backordered
Gummihärte:

Macaron Flat-Hop Bucking

Diese Buckings sind für nahezu alle standard (S-)AEGs geeignet.

Price range : €8.90 to €8.90
€8.90
This item can be backordered
Gummihärte:

Nozz-X

Extension for Nozz-X Base

Tip, one of four available.
Tips are offered in two lenghts which allow your nozzle to be between 19
and 23mm or 22,5 and 26,5mm long. Both lengths are available with small
or large chamfers (less or more sloped edges). Each combination of the
barrel, bucking and hop chamber will be different. Therefore, is some
cases a bigger chamfer will provide better seal, whereas in other small
chamfer will be more suitable. Nozz-X allows you to adjust shape of the
nozzle tip to your setup.

For more information look up Nozz-X Base

Price range : €7.49 to €7.49
€7.49
Nozz-X Fasengröße:

Nozz-X Länge:

Nozz-X Base

Nozz-X is a modular, adjustable lenght nozzle system, which allows you
to achieve perfect seal and reliable BB feeding.

Universal base.
Two o-rings with different thickness are included with each base, so
that you can choose the one which provides 100% seal and smooth nozzle
movement with most cylinder heads. The base is designed so, that it
cannot make a full revolution once in the gearbox, which allows you to
adjust the nozzle length with closed gearbox.

Combination-options

You can combine this universal base with four tips differing in length. Both lengths are available with small
or large chamfers (less or more sloped edges). Each combination of the
barrel, bucking and hop chamber will be different. Therefore, is some
cases a bigger chamfer will provide better seal, whereas in other small
chamfer will be more suitable.

Nozz-X allows you to adjust shape of the
nozzle tip to your setup.

For combination-options visit click here to visit the Nozz-X Collection.

 

Feel free to check Peruns video on the products:

<iframe width="810" height="608" src="https://www.youtube.com/embed/mXqsc3rIhpM" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

€7.49

Perun AB++ (universal wiring)

AB++

AB++ is an on-wire mosfet, channeling the power from the battery to the motor through a specialized high-power transistor, instead of delicate mechanical switches, increasing reliability and replica performance. It also enhances your replica by adding many new, useful features.

Comes with an universal wiring, that can be used in any replica. Only few easy soldering joints are needed to install the mosfet. 

Feature description

Electronic burst – Change auto to an electronically controlled burst to save your ammo and increase realism!

Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with a high rate of fire, overspin (double shot problem).

Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger while simultaneously holding the button on the unit. A shot will be fired, with no precocking and fully braked.

Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.

Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. When the battery voltage fall to a dangerously low level, the user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.

Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery if a short circuit or blocked motor is detected.

 

Programming of all the settings is done solely by using a trigger and a button on the device, in an easily memorable and quick sequences. Programming is supported by sound signals and a multicolor LED diode. That allows changing the settings at any moment, in a matter of seconds, even under enemy fire.

Upgrade kit works without problems with any battery from 7V to 17V. It can also be used with most extreme setups, without any limitations as to the spring rating.

For more information visit AB++ Manual

€51.90

Perun V2 Hybrid (back wired)

Perun V2 HYBRID

Perun V2 Hybrid replaces mechanical contacts in your airsoft replica or gel blaster and provides lots of useful features. Optical and magnetic sensors allow to eliminate many moving parts that are prone to damage, thus increasing the reliability. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.
Works without the need for any modification with most V2 gearboxes in Tokyo Marui standard. For details and exceptions please refer to the manual.

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field.
Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions.
Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).
Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked.
2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi – auto and burst – auto.
Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.
Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.
DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.
Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.
DSG – a sector gear detection mode specially prepared to work with dual sector gears.
Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.
Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolor LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.
Perun V2 Hybrid works without problems with any battery from 7V do 17V. It can also be used with most extreme setups.

 

For more information visit V2 Hybrid Manual

Or watch

€77.90

Perun V3 Hybrid (universal wiring)

Perun V3 Hybrid replaces mechanical contacts in your airsoft replica or gel blaster and provides lots of useful features. Optical and magnetic sensors allow to eliminate many moving parts that are prone to damage, thus increasing the reliability. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.
Works without the need for any modification with most V3 gearboxes in Tokyo Marui standard. For details and exceptions please refer to the manual.

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field.
Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions.
Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).
Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked.
2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi – auto and burst – auto.
Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.
Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.
DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.
Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.
DSG – a sector gear detection mode specially prepared to work with dual sector gears.
Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.
Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolor LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.
Perun V3 Hybrid works without problems with any battery from 7V do 17V. It can also be used with most extreme setups.

For more information visit: V3 Manual

€77.90

Spring Set for AEG Ver.3

€5.90

Spring Set for AEG Ver.2

€5.90

Screw for spring guide

DATA SHEET

Catalogue code VOD-SR
Material Steel C45
Weight 13,6 g
Compatible with the gearbox v.2, v.3

MORE INFO

Manufacturer: Airsoft Parts - Made in the Czech Republic

The locking screw is used to fixing the spring guide to the gearbox. The screw has a thread M5. This garantees compatibility with all our spring guides. The screw is made of steel and the surface is galvanized.

Advantages:

  • Fixed spring guide ot the mechabox
  • Prevents fracture of the spring guide when using strong springs
€3.49

Spring guide version 3

DATA SHEET

Catalogue code VOD-V3
Material Steel 1.7131
Maximum suitable spring M170
Bearings YES
Weight 27,1 g
Compatible with the gearbox v.3

MORE INFO

Producer: Airsoft parts

Spring Guide is made using a steel foot with a shiny nickel surface and a blackened nickel steel mandrel.Quality material, heat treatment and surface finishing result in no abrasion of the spring guide during shooting.A threaded hole is drilled in the bottom part of the mandrel.

The spring guide also incorporates an axial ball bearing which allows easy rotation of the spring in compression.This rotation significantly increases the service life of the spring.

€11.90

Spring guide version 2

DATA SHEET

Catalogue code VOD-V2
Material Steel 1.7131
Maximum suitable spring M170
Bearings YES
Weight 27,1 g
Compatible with the gearbox v.2

MORE INFO

Producer: Airsoft parts

Spring Guide is made using a steel foot with a shiny nickel surface and a blackened nickel steel mandrel.Quality material, heat treatment and surface finishing result in no abrasion of the spring guide during shooting.A threaded hole is drilled in the bottom part of the mandrel.

The spring guide also incorporates an axial ball bearing which allows easy rotation of the spring in compression.This rotation significantly increases the service life of the spring.

€11.90

Bullets supply cam

MORE INFO

Plastic bullets supply cam - EOS

Advantages:

  • Prolong the opening time of the hop up chamber
  • Solves problems with BBs delivery
€3.49

Ultra Light Piston with Full Metal Teeth

DATA SHEET

Catalogue code PST-UL
Material High-Strength Plastic Material
Maximum suitable spring M130
Lightweight design YES
Weight 13.3 g
Compatible with the gearbox v.2, v.3, v.6, v.7 except special gearboxes (PSG1, SR25, L85, ...)

MORE INFO

Producer: Airsoft parts

The main part of the ULTRA LIGHT piston is a lightweight plastic body, with full metal teeth.  The second tooth is remove to decrease the chance of pre-engagement by the sector gear.

The design of the plastic body is inspired by a bionic construction that ensures weight reduction. The high strength and stiffness was assure. Using this design, the weight of the piston was reduced to only 13.3 g.

The piston has a universal design for all AEG weapons except those with special gearboxes (PSG1, SR25, L85, ...). For long life, we recommend using spring to force M130 and rate of fire up to 20 RPS.

Advantages:

  • Total weight of only 13.3 g
  • Increases FPS and reduces stress gearboxes
  • Durable plastic body
  • Full-metal teeth
  • Universal design
€21.90

High Speed Piston with Full Metal Teeth

DATA SHEET

Catalogue code PST-HS
Material High-Strength Plastic Material
Maximum suitable spring M140
Lightweight design YES
Weight 14.5 g
Compatible with the gearbox v.2, v.3, v.6, v.7 except special gearboxes (PSG1, SR25, L85, ...)

MORE INFO

Producer: Airsoft parts

The piston contain of a very durable plastic body and a full metal teeth (14 pcs). The second tooth is remove to decrease the chance of pre-engagement by the sector gear.

182 holes are drilled in the plastic body of the piston, which significantly reduces the total weight. By reducing the weight, the piston's movement speed increases during the shot, thus increasing FPS and reducing the dynamic stress of the gearbox.

The universal design of the piston allows use on low, high and very high cadence weapons. We recommend using springs up to M140.

The piston is designed for all AEG weapons except special gearboxes (PSG1, SR25, L85, ...)

Color: red, black

Advantages: 

  • Total weight of only 14.5 g
  • Increases FPS and reduces stress gearboxes
  • Durable plastic body 
  • Full-metal teeth
  • Universal design
€17.90

AEG Piston with Full Metal Teeth

DATA SHEET

Catalogue code PST
Material High-Strength Plastic Material
Maximum suitable spring M160
Lightweight design NO
Weight 15,6g
Compatible with the gearbox v.2, v.3, v.6, v.7 except special gearboxes (PSG1, SR25, L85, ...)

MORE INFO

Producer: Airsoft parts

The piston contain of a very durable plastic body and a full metal teeth (14 pcs). The second tooth is remove to decrease the chance of pre-engagement by the sector gear. Total weight is only 15.6g

The piston is designed for all AEG weapons except special gearboxes (PSG1, SR25, L85, ...)

Advantages: 

  • Very low weight  
  • Durable plastic body 
  • Full-metal teeth
  • Universal design

New generation 1.2:

  • Modified holes on the front site

Video:

 

 

€15.90

Cylinder head CLASSIC

DATA SHEET

Catalogue code HV-CLAS
Dimension Standard
Material EN AW 6012 T6
Maximum suitable spring M150
Seal 2 pcs O-ring
Surface finishing Electroless nickel
Rubber pad Molded rubber plate
Hardness of rubber pad 70 ShA
Weight 11,3 g
Compatible with the gearbox v.2, v.3

MORE INFO

Producer: Airsoft parts

The cylinder head is made of duralumin EN AW 6012 on CNC machining center.The seal between the cylinder head and the cylinder is ensured by two O-rings. The rubber pad surface is fixed to the duralumin body by mechanical locks and high strength adhesive.

Advantages:
• Inner tapering to facilitate airflow into the nozzle
• Massive construction
• Shaped rubber pad

€11.90

Piston head - POM

Catalogue code HP-POM
Dimension Standard
Material Tecaform (POM)
Maximum suitable spring M150
Seal 1 pcs O-ring
Lightweight design NO
Surface finishing Without surface finishing
Bearings YES
Weight 8,6 g
Compatible with the gearbox v.2, v.3, v.7

MORE INFO

Producer: Airsoft parts
The piston head is made of a structural plastic TECAFORM also known as POM on the CNC machine. Nine holes are drilled on the front side.The air stream flows through these holes during compression thus expanding the O-ring which provides for better sealing of the space between the piston head and the cylinder.

The centre of the piston head is passed through by the lock nut, which spreads the clamping force over a larger area and therefore prevents breakage of the bolt from the body of the piston head.

This piston head also incorporates an axial ball bearing.

Advantages:

  • High resistance
  • Perfect sealing
  • Axial ball bearing for easy spring rotation
  • Plastic nut that reduces total weight
€11.90

Silent Cylinder Head

DATA SHEET

Catalogue code HV-TICH
Dimension Standard
Material EN AW 6012 T6
Maximum suitable spring M170
Seal 1 pcs special U-rings
Surface finishing Electroless nickel
Rubber pad Combined with seal
Hardness of rubber pad 80 ShA
Weight 10,1
Compatible with the gearbox v.2, v.3

MORE INFO

Producer: Airsoft parts

The cylinder head is made of duralumin EN AW 6012 on CNC machining centre.This head is a completely innovative design. The most significant difference is the rubber pad and single-piece seal.

Advantages:

  • Without leakage between the cylinder head and the cylinder
  • Large rubber pad surface suitable for the strong springs
  • Seals and impact surface made of a single piece 
  • Long lifetime
  • Low noise level

 

€11.90

G&G Cold-Resistant Hop-Up Rubber

€8.50
This item can be backordered

Filter by Price


0 10000.00 To €1000.00

Filter by Brands